Teste do meu HD com Gsmartcontrol

1. Teste do meu HD com Gsmartcontrol

L. GUSTAVO
lgfcosta

(usa Linux Mint)

Enviado em 23/08/2020 - 16:14h

Caros, boa tarde.

Resolvi realizar testes no meu HD pelo gsmartcontrol e 4 erros foram listados. Fiquei confuso com a análise, alguém pode me ajudar a desvendar se preciso me preocupar?
Desde já agradeço.

Linux mint 20 xfce.


smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-26-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-22ZCT0
Serial Number: WD-WXK1A2040555
LU WWN Device Id: 5 0014ee 2aef0bc12
Firmware Version: 11.01A11
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Sun Aug 23 18:13:58 2020 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 113) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 2
3 Spin_Up_Time POS--K 189 187 021 - 1550
4 Start_Stop_Count -O--CK 095 095 000 - 5387
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 081 081 000 - 14168
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 095 095 000 - 5297
192 Power-Off_Retract_Count -O--CK 200 200 000 - 172
193 Load_Cycle_Count -O--CK 180 180 000 - 62503
194 Temperature_Celsius -O---K 106 091 000 - 41
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning

General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 4
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 08 00 51 00 00 e0 01 00 00

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 51 25 a6 0e 00 00 00 00 00 01 00 09 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
00 08 00 00 c0 a6 51 09 0e 25 00 01 00 00:00:51.208 NOP [Abort queued commands]
09 50 25 a6 0e 00 08 00 b8 00 01 00 09 07:40:59.856 [RESERVED]
00 08 00 00 a8 a6 50 09 0e 25 00 01 00 00:00:45.064 NOP [Abort queued commands]

Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 e0 01 00 00

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 8a 25 a6 01 00 00 00 00 00 01 00 09 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
00 00 00 00 00 a6 7c 09 01 25 00 01 00 00:00:00.000 NOP [Abort queued commands]
09 4a 35 a6 01 00 00 00 00 00 01 00 08 07:40:56.571 [RESERVED]
00 60 00 00 a0 a6 49 01 01 35 00 01 00 00:00:24.608 NOP [Abort queued commands]

Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
01 -- 00 01 08 00 51 00 00 e0 01 00 00

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 7c 25 02 b2 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
00 40 00 00 62 02 70 00 b2 25 00 00 00 00:00:38.920 NOP [Abort queued commands]
00 65 25 02 b2 00 08 00 d8 00 00 00 00 00:02:56.741 NOP [Reserved subcommand] [OBS-ACS-2]
00 08 00 00 40 02 58 00 b2 25 00 00 00 00:00:36.872 NOP [Abort queued commands]

Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 e0 01 00 00

Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 6d 25 02 a5 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
00 08 00 00 d8 02 81 03 a4 25 00 00 00 00:00:00.000 NOP [Abort queued commands]
01 74 35 02 a3 00 40 00 80 00 00 00 01 00:02:53.161 [RESERVED]
00 08 00 00 a0 02 73 04 a3 35 00 00 00 00:00:22.536 NOP [Abort queued commands]

SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 14168 -
# 2 Extended offline Completed without error 00% 14059 -
# 3 Short offline Completed without error 00% 14057 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version: 2
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 34/48 Celsius
Lifetime Min/Max Temperature: 41/57 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: 1/85 Celsius
Temperature History Size (Index): 128 (51)

Index Estimated Time Temperature Celsius
52 2020-08-23 16:06 35 ****************
... ..( 4 skipped). .. ****************
57 2020-08-23 16:11 35 ****************
58 2020-08-23 16:12 34 ***************
59 2020-08-23 16:13 34 ***************
60 2020-08-23 16:14 34 ***************
61 2020-08-23 16:15 35 ****************
62 2020-08-23 16:16 35 ****************
63 2020-08-23 16:17 35 ****************
64 2020-08-23 16:18 36 *****************
65 2020-08-23 16:19 37 ******************
66 2020-08-23 16:20 38 *******************
67 2020-08-23 16:21 39 ********************
68 2020-08-23 16:22 40 *********************
69 2020-08-23 16:23 41 **********************
70 2020-08-23 16:24 41 **********************
71 2020-08-23 16:25 42 ***********************
72 2020-08-23 16:26 42 ***********************
73 2020-08-23 16:27 43 ************************
74 2020-08-23 16:28 43 ************************
75 2020-08-23 16:29 44 *************************
76 2020-08-23 16:30 44 *************************
77 2020-08-23 16:31 44 *************************
78 2020-08-23 16:32 45 **************************
... ..( 2 skipped). .. **************************
81 2020-08-23 16:35 45 **************************
82 2020-08-23 16:36 46 ***************************
... ..( 2 skipped). .. ***************************
85 2020-08-23 16:39 46 ***************************
86 2020-08-23 16:40 47 ****************************
... ..( 4 skipped). .. ****************************
91 2020-08-23 16:45 47 ****************************
92 2020-08-23 16:46 48 *****************************
... ..( 22 skipped). .. *****************************
115 2020-08-23 17:09 48 *****************************
116 2020-08-23 17:10 47 ****************************
... ..( 19 skipped). .. ****************************
8 2020-08-23 17:30 47 ****************************
9 2020-08-23 17:31 46 ***************************
... ..( 25 skipped). .. ***************************
35 2020-08-23 17:57 46 ***************************
36 2020-08-23 17:58 45 **************************
37 2020-08-23 17:59 45 **************************
38 2020-08-23 18:00 45 **************************
39 2020-08-23 18:01 44 *************************
40 2020-08-23 18:02 44 *************************
41 2020-08-23 18:03 44 *************************
42 2020-08-23 18:04 43 ************************
43 2020-08-23 18:05 43 ************************
44 2020-08-23 18:06 42 ***********************
... ..( 3 skipped). .. ***********************
48 2020-08-23 18:10 42 ***********************
49 2020-08-23 18:11 41 **********************
50 2020-08-23 18:12 41 **********************
51 2020-08-23 18:13 41 **********************

SCT Error Recovery Control:
Read: Disabled
Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x8000 4 8597 Vendor specific




  






Patrocínio

Site hospedado pelo provedor RedeHost.
Linux banner

Destaques

Artigos

Dicas

Tópicos

Top 10 do mês

Scripts